Helixyte™ iFluor® 647 Nucleic Acid Labeling Dye *Optimized for Labeling 2x100 ug DNA/RNA*

1. Combine DNA with the Helixyte™ iFluor® 647 Nucleic Acid Labeling Dye stock solution.

2. Incubate for 1 hour at 37°C.

3. Purify the conjugate as required for downstream applications.

Unless otherwise noted, all unused stock solutions should be divided into single-use aliquots and stored at -20 °C after preparation. Avoid repeated freeze-thaw cycles

Before opening the vial, thaw Helixyte™ iFluor® nucleic acid labeling dye at room temperature. Briefly centrifuge to collect the dried pellet.

1. Add 70 μL of DMSO to the Helixyte™ iFluor® 647 Nucleic Acid Labeling Dye vial to prepare a 10 mM stock solution.

   Note: It is recommended to divide any unused stock solution into single-use aliquots. Store the aliquots at ≤-20 ºC and protect them from light. Avoid repeated freeze-thaw cycles.

1. Prepare the labeling reaction according to the specifications in table 1 below.

   Table 1. Standard Nucleic Acid Labeling Reaction.

   Components	Volume added to reaction	Final Concentration
   DNA (1 mg/mL)	2 to 5 µL	2 to 5 µg
   Helixyte™ iFluor® 647 Nucleic acid Labeling Dye stock solution	1 µL	100 µM
   TE Buffer (pH 8 to 8.5)	Add sufficient buffer to adjust the volume to 100 µL

    

   Note: This DNA:Dye ratio results in labeling efficiencies that are appropriate for most applications. The amount of Helixyte™ iFluor® 647 Nucleic Acid Labeling Dye or the reaction incubation time can be adjusted to modify the labeling density as per the application requirements. The DNA-to-dye ratio must be optimized to achieve a higher labeling ratio.

2. Incubate the reaction at 37℃ for 1 hour, protected from light.

   Note: After 30 minutes of incubation, briefly centrifuge the reaction to minimize the effects of evaporation and maintain the appropriate concentration of the reaction components.

   Note: Alternatively, the reaction can be incubated at room temperature for 2 hours. For the best labeling condition, we recommend incubating at 37℃.

3. After incubation, the labeling mix can be purified to remove any free labeling dye. Refer to the “Purification of labeling mix with alcohol precipitation” section below for instructions.

1. Add 0.1 volume (10 uL) of 5M sodium chloride and 2 - 2.5 volumes of ice-cold 100% ethanol (250 uL) to the reaction. Mix well and place at ≤ -20°C for at least 30 minutes.

2. Centrifuge at full speed (>14,000 x g) in a refrigerated micro centrifuge for 15-30 minutes to pellet the labeled nucleic acid. Once pelleted, carefully remove the ethanol with a micropipette. Do not disturb the pellet.

   Note: Small nucleic acid quantities can be difficult to visualize. Mark and orient the precipitate-containing tubes in the microfuge such that the pellet will form in a predetermined place.

3. Wash the pellet once with 500 μL of room temperature 70% ethanol. Centrifuge at full speed for an additional 15-30 minutes.

4. Remove all traces of ethanol with a micropipette. DO NOT allow the sample to dry longer than 5 minutes as the pellet may become difficult to resuspend.

5. Resuspend the labeled DNA with ~ 30 µL sterile water.

6. Store the purified, labeled nucleic acid for long-term storage or put on ice for immediate use.